Asphalt Calculator
Work out how much asphalt you need for a driveway, parking lot, or path — in tons, cubic yards, and cubic feet — before you call the supplier.
Asphalt Calculator
Density defaults to 145 lb per cubic foot for compacted hot-mix asphalt. Mixes vary: check with your supplier if they quote a different density.
Formulas:
Volume (cu ft) = Length (ft) × Width (ft) × Thickness (in) ÷ 12
Volume (cu yd) = Volume (cu ft) ÷ 27
Weight (lb) = Volume (cu ft) × density (145 lb/cu ft compacted)
Tons = Weight (lb) ÷ 2,000
What Does an Asphalt Calculator Do?
An asphalt calculator works out how much hot-mix asphalt you need for a driveway, parking lot, path, or patch job, and converts that amount into the units suppliers actually sell by: tons and cubic yards. You enter the length, width, and thickness of the area, and the calculator returns the volume, the weight, and the tonnage to order — including a waste allowance for spillage, uneven ground, and compaction.
Getting this number right matters because asphalt is sold by weight and laid hot. Order too little and the crew runs out with part of the driveway unpaved, leaving a cold joint that will crack and let water in. Order too much and you have paid for tons of material that cools and hardens before it can be used. A calculator takes the guesswork out of the order, and it lets you compare quotes from different suppliers on a like-for-like basis.
How to Use This Calculator
Measure the area in feet: the length and the width of the surface you are paving. Then enter the thickness in inches — 2 to 3 inches of compacted asphalt is standard for a residential driveway over a prepared gravel base, and 3 to 4 inches for a parking lot or any surface that will carry heavier vehicles. The density field defaults to 145 pounds per cubic foot, the standard figure for compacted hot-mix asphalt; leave it there unless your supplier quotes a different mix density. Finally, set the waste allowance — 5% is the usual figure for a straightforward rectangular job, and 10% is safer for irregular shapes or rough ground.
The headline result is tons, because that is how asphalt plants price and deliver it. The cubic yard and cubic foot figures are there for comparison: some contractors quote by the yard, and knowing both numbers lets you check that a quote is consistent. The "volume before waste" line shows the exact geometric volume of the job, so you can see exactly how much the waste allowance added.
The Asphalt Formula
The volume of a rectangular paved area is length times width times thickness. The only wrinkle is the units: length and width are measured in feet, but thickness is measured in inches, so thickness must be divided by 12 first. A driveway 20 feet long and 12 feet wide, paved 3 inches thick, is 20 × 12 × 3 ÷ 12 = 60 cubic feet. Divide cubic feet by 27 to get cubic yards (there are 27 cubic feet in a cubic yard), so the same driveway is 2.22 cubic yards.
Weight comes from density. Compacted hot-mix asphalt weighs about 145 pounds per cubic foot — that is the figure used by most state highway departments and asphalt associations for estimating. Multiply 60 cubic feet by 145 and you get 8,700 pounds, or 4.35 tons (a US ton is 2,000 pounds). With a 5% waste allowance, the volume becomes 63 cubic feet, or 2.33 cubic yards, weighing 9,135 pounds — 4.57 tons. That is the number to give the supplier.
Note that 145 pounds per cubic foot is the density of asphalt after compaction. Loose asphalt in a truck is lighter per cubic foot, and different mixes — a coarse binder course versus a fine surface course, or a mix with recycled content — can run from about 140 to 155 pounds per cubic foot. The difference is small, but on a large parking lot it adds up: a 5% density difference on a 100-ton job is 5 tons. If your supplier quotes a specific density for their mix, enter it in the density field.
How Thick Should Asphalt Be?
Thickness depends on what the surface has to carry and what is underneath it. A residential driveway for cars needs 2 to 3 inches of asphalt over 4 to 6 inches of compacted gravel base. The base does most of the structural work: it spreads the load and drains water away from the asphalt. Skimping on the base to save money is the most common reason driveways fail early — the asphalt itself is only as good as what it sits on.
A parking lot or a driveway that will carry delivery trucks, RVs, or other heavy vehicles needs 3 to 4 inches of asphalt, often laid in two lifts (layers): a thicker binder course underneath and a thinner surface course on top. Commercial and industrial pavements can go to 6 inches or more. A thin overlay on an existing sound driveway — sometimes called a resurface — is typically 1.5 to 2 inches, but it only works if the existing pavement is structurally sound; paving over a cracked, failing base just hides the problem for a season.
Worked Example
Say you are paving a driveway 20 feet long and 12 feet wide, 3 inches thick, over a prepared gravel base. The volume is 20 × 12 × 3 ÷ 12 = 60 cubic feet, which is 60 ÷ 27 = 2.22 cubic yards. At 145 pounds per cubic foot, that is 8,700 pounds, or 4.35 tons. Add a 5% waste allowance and you should order 4.57 tons — round up to 5 tons, since most plants deliver in whole-ton increments and a little extra is far cheaper than a short load. At a typical delivered price of $100 to $200 per ton (prices vary widely by region and by year), the material for this driveway runs roughly $500 to $1,000, before the cost of the base, labor, and equipment.
For a bigger job — a parking lot 50 feet by 40 feet at 4 inches thick — the volume is 50 × 40 × 4 ÷ 12 = 666.67 cubic feet, or 24.69 cubic yards. At 145 pounds per cubic foot that is 96,667 pounds, or 48.33 tons; with 5% waste, 50.75 tons. On a job this size, confirming the mix density with the plant is worth doing: at 150 pounds per cubic foot instead of 145, the same volume weighs 50 tons before waste.
Tips for Ordering Asphalt
Measure the area, not the old pavement. If you are replacing an existing driveway, measure the finished area you want, not the cracked edges of the old one. Old pavement often spreads or crumbles at the edges, so measuring it can overstate the area.
Confirm how the supplier sells. Most plants sell by the ton and deliver by the truckload — a typical dump truck carries about 20 tons. For a small job under 5 tons, ask about a minimum load charge; some plants charge extra for small deliveries, which can make bagged cold-patch asphalt the cheaper option for a tiny repair.
Schedule for warm, dry weather. Asphalt needs to be laid and compacted while it is hot, ideally above 50 degrees Fahrenheit, and it should not be laid on wet ground or in rain. A cold or wet install compacts poorly and will not last.
Allow for compaction. Asphalt is laid loose and then rolled, and it compacts by roughly 20 to 25% — a 4-inch loose layer compacts to about 3 inches. The thickness in this calculator is the finished, compacted thickness, which is what your design calls for; the crew handles the loose-depth adjustment.
Common Mistakes to Avoid
The biggest mistake is entering the thickness in feet instead of inches, which makes the volume 12 times too large. If the answer looks wildly wrong, check the units first. The second mistake is forgetting the waste allowance: forms and edges are never perfect, some material sticks to the truck, and a job calculated with zero waste will run short. Five percent is the standard; use 10% for irregular shapes.
The third mistake is paving too thin over a weak base. A 2-inch layer over soft, uncompacted soil will crack under a car within a season or two. Spend the money on the gravel base and compaction — it is the cheapest insurance a driveway can have. Finally, do not forget drainage: asphalt should slope away from buildings at roughly 2% (about a quarter inch per foot) so water runs off instead of pooling and weakening the surface.
Results from this calculator are estimates for planning and ordering. Your contractor or asphalt supplier can confirm the mix density and the right thickness for your soil and traffic conditions.
Frequently Asked Questions
How many tons of asphalt do I need for a 20x12 driveway 3 inches thick?
4.35 tons before waste, or 4.57 tons with a 5% waste allowance. The volume is 20 x 12 x 3 / 12 = 60 cubic feet (2.22 cubic yards), and at 145 lb per cubic foot that weighs 8,700 lb.
How much does one cubic yard of asphalt weigh?
About 3,915 lb, or just under 2 tons. A cubic yard is 27 cubic feet, and compacted asphalt weighs about 145 lb per cubic foot (27 x 145 = 3,915).
How thick should asphalt be for a residential driveway?
2 to 3 inches of compacted asphalt over 4 to 6 inches of compacted gravel base. Driveways that carry heavy vehicles need 3 to 4 inches, and the gravel base matters as much as the asphalt thickness.
What density should I use for asphalt?
145 lb per cubic foot is the standard figure for compacted hot-mix asphalt. Mixes vary from about 140 to 155 lb per cubic foot, so use your supplier's figure if they quote one.
How much waste should I add when ordering asphalt?
5% is standard for a straightforward rectangular job. Use 10% for irregular shapes, rough ground, or a job with many edges and curves. Running short mid-pour leaves a cold joint that will crack.