Brick Calculator
Work out how many bricks and how much mortar a wall needs — deducting doors and windows and adding waste for cuts and breakage.
Brick Calculator
Based on standard modular bricks (3-5/8 x 2-1/4 x 8 in) with 3/8 inch mortar joints: 6.75 bricks per square foot, about 4.5 lb each. One 80 lb bag of mortar mix makes about 0.6 cu ft.
Formulas:
Bricks = (Wall area − Openings) × 6.75 bricks per sq ft, plus the waste percentage
Mortar = Bricks × 0.00806 cu ft (3/8 in bed and head joints); one 80 lb bag makes 0.6 cu ft
Weight = Bricks × 4.5 lb
What This Brick Calculator Does
Brick is ordered by the thousand, but walls are measured in feet — and the conversion between the two is where most ordering mistakes happen. This calculator bridges that gap. Enter the wall length and height, subtract any doors and windows, add a waste allowance for cuts and breakage, and it tells you how many bricks to order, how much mortar they need, and how much the whole lot will weigh.
The figures are based on the standard modular brick, which measures 3-5/8 inches wide, 2-1/4 inches high, and 8 inches long, laid with 3/8 inch mortar joints. With joints included, each brick covers about 21.3 square inches of wall face, which works out to 6.75 bricks per square foot. That figure — 6.75 bricks per square foot — is the one number every bricklayer knows by heart, and it is the heart of this calculator.
How to Use the Calculator
Measure the wall in feet, length by height. Then work out the area of any openings: a standard door is 3 by 7 feet, or 21 square feet, and a typical window is 3 by 4 feet, or 12 square feet. Add the opening areas together and enter the total. The calculator subtracts them from the wall area before counting bricks — but note that openings also create extra cutting waste around their edges, which is one reason the waste allowance matters.
Set the waste allowance last. Ten percent is standard for a plain rectangular wall; use 15% if the wall has many openings, corners, or arches, because every cut produces a piece you may not be able to use. The results update as you type, so you can see at a glance how a bigger window or a taller wall changes the order.
How Many Bricks per Square Foot?
The answer depends on the brick size and the joint thickness. For the standard modular brick with 3/8 inch joints, the figure is 6.75 bricks per square foot. Here is where that comes from: the face of a brick plus its share of the joints is 8-3/8 inches long (8 inches of brick plus a 3/8 inch head joint) by 2-5/8 inches high (2-1/4 inches of brick plus a 3/8 inch bed joint). That is 21.98 square inches per brick, and 144 square inches per square foot divided by 21.98 gives 6.55 bricks — but the industry figure of 6.75 accounts for the way joints are shared between neighbouring bricks and for the small fraction of bricks lost to breakage in practice. The calculator uses the industry-standard 6.75.
Other brick sizes give different figures. A standard-size brick (3-5/8 by 2-1/4 by 8 inches) is the same as the modular brick in face area, so it also runs 6.75 per square foot. Larger bricks cover more area each and need fewer per square foot, which is why king-size and queen-size bricks are popular for big commercial walls: fewer bricks means faster laying and lower labour costs, even though each brick costs more.
How Much Mortar Does Brickwork Need?
Each brick needs mortar in two places: the bed joint underneath it and the head joint at one end. The bed joint is 8 inches long, 3-5/8 inches wide, and 3/8 inch thick, which is 10.875 cubic inches. The head joint is 3-5/8 inches wide, 2-1/4 inches high, and 3/8 inch thick, which is 3.06 cubic inches. Together that is 13.94 cubic inches, or 0.00806 cubic feet, of mortar per brick.
A wall of 540 bricks therefore needs 540 × 0.00806 = 4.35 cubic feet of mortar. One 80 lb bag of mortar mix makes about 0.6 cubic feet, so that wall needs 8 bags. As a rule of thumb, one bag of mortar covers roughly 65 to 70 bricks — which is a handy check when you are standing in the store. If your figure is far from that ratio, double-check the wall area.
Worked Example: A 10 × 8 Wall With a Door
Take a wall 20 feet long and 10 feet high with one standard door opening of 21 square feet, and a 10% waste allowance. The gross wall area is 20 × 10 = 200 square feet. Subtracting the door leaves 179 square feet of brickwork. At 6.75 bricks per square foot, that is 179 × 6.75 = 1,208.25 bricks, rounded up to 1,209. With 10% waste, the order is 1,209 × 1.10 = 1,330 bricks. The mortar needed is 1,330 × 0.00806 = 10.72 cubic feet, which is 10.72 ÷ 0.6 = 18 bags at 80 lb. The bricks weigh 1,330 × 4.5 = 5,985 lb — just under 3 tons.
For a smaller job, a 10 by 8 foot garden wall with no openings needs 80 × 6.75 = 540 bricks before waste, or 594 with 10% waste. The mortar is 4.35 cubic feet without waste (8 bags) or 4.79 cubic feet with waste (still 8 bags, since the extra mortar does not push past the next whole bag). The bricks weigh 2,430 lb without waste, or 2,673 lb with it. Bricks are usually sold by the thousand on pallets of about 500, so the garden wall is a little over one pallet.
Brick Veneer vs. Structural Brick
Most modern brick walls are veneer, not structural. A veneer wall is a single layer of brick — one brick thick, or 4 inches including the mortar — attached to a wood or steel-framed wall behind it with metal wall ties. The brick carries only its own weight; the frame behind it carries the building. This calculator counts bricks for a single-wythe wall, which is exactly what a veneer is.
A structural brick wall, by contrast, is two or more wythes thick and carries the load of the building itself. These are rare in new residential construction but common in older buildings. If you are rebuilding a double-wythe wall, double the brick count — and double the mortar too, since the collar joint between the wythes also takes mortar. For a double-wythe wall, the weight doubles as well: the 10 × 8 wall above would weigh about 4,860 lb instead of 2,430 lb.
Tips for Ordering Brick
Order from one batch. Bricks vary slightly in color between kiln batches. Order the full quantity at once, from the same pallet run, so the wall is a consistent color. If you run short and order more later, the new bricks may be a visibly different shade.
Mix bricks from several pallets. Even within one batch there is some variation. Masons blend bricks from three or four pallets as they work, which spreads the variation evenly instead of leaving a visible band where one pallet ended and the next began.
Keep bricks dry before laying. Wet bricks absorb water from the mortar and weaken the bond. Store pallets under cover, and if bricks get rained on, let them dry before use. Very dry bricks on a hot day can be lightly dampened, but they should never be soaked.
Check the return policy. Most suppliers will take back unopened pallets, sometimes with a restocking fee. It is cheaper to order 10% extra and return a few bricks than to run short and pay for a second delivery — or worse, get bricks from a different batch.
Common Mistakes to Avoid
The biggest mistake is forgetting to subtract openings — or subtracting them twice. Measure each opening once, add the areas, and enter the total. The second mistake is using the wrong bricks-per-square-foot figure for the brick size you actually bought. If you are using a larger brick, 6.75 per square foot will over-order; check the manufacturer's figure for your brick.
The third mistake is under-ordering mortar. Mortar is cheap compared with bricks, but running out mid-wall means a trip to the store and a cold joint in the work. Buy one extra bag beyond what the calculator says — it keeps well if stored dry, and it is cheap insurance.
Finally, do not forget the wall ties, flashing, and weep holes on a veneer wall. Ties hold the brick to the frame, flashing directs water out at the base, and weep holes let it escape. A veneer wall without weep holes traps moisture behind the brick, which causes damp problems inside the building. None of these are counted by this calculator, but all of them are essential to the finished wall.
Frequently Asked Questions
How many bricks do I need for a 10x8 wall?
540 bricks before waste, or 594 bricks with a 10% waste allowance. The wall is 80 square feet, and standard modular bricks run 6.75 per square foot (80 x 6.75 = 540).
How many bricks are in a square foot?
6.75 bricks per square foot for standard modular bricks (3-5/8 x 2-1/4 x 8 in) with 3/8 inch mortar joints. Larger bricks need fewer per square foot.
How many bags of mortar do I need for 1,000 bricks?
About 14 bags at 80 lb each. Each brick uses about 0.00806 cubic feet of mortar, so 1,000 bricks need 8.06 cubic feet, and one bag makes 0.6 cubic feet (8.06 / 0.6 = 13.4, rounded up to 14).
How much does a brick weigh?
About 4.5 lb for a standard modular brick. A pallet of 500 bricks weighs roughly 2,250 lb, and 1,000 bricks weigh about 4,500 lb.
Should I subtract doors and windows when counting bricks?
Yes. Measure each opening in square feet and subtract the total from the wall area before multiplying by 6.75. A standard 3x7 foot door is 21 square feet, which saves about 142 bricks.