Concrete Block Calculator

By Asira Tools Team · Last updated 20 November 2026

Work out how many concrete blocks and bags of mortar a wall needs — courses, blocks per course, and total weight included.

Advertisement

Concrete Block Calculator

106 blocks
Wall area80 sq ft
Blocks per course8 blocks
Courses12 courses
Mortar needed4.42 cu ft
80 lb mortar bags8 bags
Wall weight4,028 lb

Based on standard 8x8x16 inch concrete masonry units (CMU) with 3/8 inch mortar joints. Each block weighs about 38 lb. Mortar figures assume full bed and head joints; one 80 lb bag of mortar mix makes about 0.6 cu ft.

Formulas:

Blocks per course = Wall length (in) ÷ 16, rounded up

Courses = Wall height (in) ÷ 8, rounded up

Blocks = Blocks per course × Courses, plus the waste percentage

Mortar = Blocks × 0.0417 cu ft (3/8 in bed and head joints); one 80 lb bag makes 0.6 cu ft

What This Block Calculator Does

Concrete blocks — also called concrete masonry units, or CMU — are the standard material for foundation walls, retaining walls, garden walls, and outbuildings. This calculator works out how many blocks a wall needs, how many courses high it will be, how much mortar to buy, and how much the finished wall will weigh. Enter the wall length and height in feet, add a waste allowance, and the quantities appear.

The numbers are based on the standard block, which measures 8 inches high, 8 inches deep, and 16 inches long. That size is no accident: with a 3/8 inch mortar joint, each block occupies exactly 8 by 16 inches of wall face, which makes the maths clean. One square foot of wall takes 1.125 blocks, so a 10-foot wall that is 8 feet high — 80 square feet — needs 90 blocks by area. The calculator works it out by courses instead, which is slightly more accurate: 8 blocks per course across 10 feet, 12 courses up 8 feet, giving 96 blocks before waste.

How to Use the Calculator

Measure the wall in feet: the length along the ground and the height from the footing to the top. If the wall has a door or window opening, work out the wall in sections around the opening and add them together — or subtract the opening area at 1.125 blocks per square foot. A standard door opening of 3 by 7 feet is 21 square feet, which saves about 24 blocks.

Set the waste allowance last. Ten percent is the usual figure and covers broken blocks, cut pieces, and the half blocks needed at corners and ends. Blocks are heavy and brittle, so a few always crack in delivery or during cutting. The results update as you type, so you can try different heights and see how the block count changes — every extra course on a 10-foot wall adds 8 blocks.

Understanding Block Sizes

The standard block is called 8x8x16, but those are nominal dimensions. The actual block is 7-5/8 inches high, 7-5/8 inches deep, and 15-5/8 inches long — the missing 3/8 inch is the mortar joint. This is why the maths works out so neatly: block plus joint equals exactly 8 by 16 inches of wall face, and 8 blocks laid end to end span 10 feet 8 inches including joints, while 12 courses reach exactly 8 feet.

Other sizes exist for special jobs. Half blocks are 8 inches long and fill the gaps at corners and ends where a full block would not fit. Four-inch blocks are used for partition walls and veneers. Bond beam blocks have a channel along the top that holds a horizontal reinforcing bar and grout. Corner blocks have a finished end for exposed corners. For most walls, though, the standard 8x8x16 block does the job, with half blocks handling the edges.

How Much Mortar Does a Block Wall Need?

Each block sits on a bed joint of mortar 3/8 inch thick and has a head joint of the same thickness at one end. The bed joint covers the top of the block below — 16 by 8 inches — and the head joint covers the end — 8 by 8 inches. Together they use 72 cubic inches of mortar per block, which is 0.0417 cubic feet. A 96-block wall therefore needs 96 × 0.0417 = 4 cubic feet of mortar, which is 7 bags at 80 lb each, since one bag makes about 0.6 cubic feet.

That figure assumes full mortar bedding, where the whole top surface of the block gets mortar. Some masons use face-shell bedding instead, putting mortar only on the two outer edges of the block, which uses roughly half as much mortar. Face-shell bedding is common on garden walls and other non-load-bearing work, but full bedding is stronger and is the standard for foundation and retaining walls. If your mason uses face-shell bedding, halve the mortar figure.

Worked Example: A 10 × 8 Garden Wall

Suppose you are building a garden wall 10 feet long and 8 feet high. The wall area is 80 square feet. Each course needs 120 inches ÷ 16 = 7.5 blocks, rounded up to 8 blocks. The height needs 96 inches ÷ 8 = 12 courses. So the wall takes 8 × 12 = 96 blocks before waste, or 106 blocks with a 10% waste allowance. The mortar needed is 96 × 0.0417 = 4 cubic feet without waste — 7 bags at 80 lb — or 4.42 cubic feet and 8 bags with the waste allowance applied to the block count. The finished wall weighs about 96 × 38 = 3,648 lb without waste, or 4,028 lb with the extra blocks.

That weight is worth thinking about before you start. Nearly two tons of blocks need a proper footing — a concrete strip at least 8 inches deep and twice as wide as the wall, on undisturbed ground. A block wall built straight on soil will settle unevenly and crack. The footing for this wall would be roughly 10 feet long, 16 inches wide, and 8 inches deep, which is about 8.9 cubic feet of concrete — you can check that with the concrete calculator.

Reinforcement and Grout

A block wall over 4 feet high, or any wall holding back soil, needs reinforcement. The usual method is vertical steel bars dropped into the hollow cores of the blocks, spaced 4 feet apart, with the cores then filled with grout — a fluid concrete mix that flows around the bars and locks them in. Horizontal reinforcement goes in a bond beam course at the top of the wall, and in every fourth course on taller walls.

Grout adds a lot of weight and cost. A single core of an 8-inch block holds about 0.1 cubic feet of grout per foot of height, so grouting every core of an 8-foot wall uses roughly 0.8 cubic feet per block column. For the 10-foot wall in the example, grouting every fourth course vertically — three bars — would add about 2.4 cubic feet of grout. Your local building code sets the exact requirements, and for retaining walls over 4 feet most areas require an engineered design.

Tips for Building a Block Wall

Start with a level footing. Every course follows the one below it, so a footing that is out of level by half an inch becomes a wall that is out of plumb by half an inch. Spend the time getting the first course perfect — it is the only course you can easily fix.

Stagger the joints. Each course should be offset by half a block from the one below, so the vertical joints do not line up. Stacked joints create a weak line straight up the wall. Half blocks at the ends make the stagger work out.

Keep the mortar joints consistent. A 3/8 inch joint is the standard. Thicker joints waste mortar and weaken the wall; thinner joints leave gaps. Use a story pole — a length of timber marked every 8 inches — to check the height as you go.

Protect fresh work from rain and frost. Mortar that gets soaked before it sets loses strength, and mortar that freezes before it cures never reaches full strength. Cover a new wall with plastic sheeting if rain or frost is forecast within 24 hours.

Common Mistakes to Avoid

The most common mistake is forgetting that blocks are sold by the pallet and delivered by the truckload, and underestimating the delivery cost. A pallet holds about 90 standard blocks — roughly 3,400 lb — so a 96-block wall is more than a full pallet. Check whether the supplier charges per pallet or per delivery, and whether they will take back unopened pallets.

The second mistake is cutting blocks with a hammer instead of a masonry saw. Hammer-cut blocks split unevenly and waste material; a saw gives a clean cut and a better fit. For a wall with many cuts, a saw rental pays for itself in saved blocks.

The third mistake is building a wall taller than 4 feet without checking local codes. Many areas require a permit and an engineered design for retaining walls over 4 feet, and some require it for any wall over 6 feet. The fine for building without a permit is far more than the permit costs, and an unpermitted wall can cause problems when you sell the property.

Advertisement

Frequently Asked Questions

How many concrete blocks do I need for a 10x8 wall?

96 blocks before waste, or 106 blocks with a 10% waste allowance. That is 8 blocks per course across 10 feet and 12 courses up 8 feet (8 x 12 = 96).

How many blocks are in a square foot of wall?

1.125 blocks per square foot for standard 8x8x16 blocks with 3/8 inch mortar joints. An 80 square foot wall needs about 90 blocks by area, though counting by courses is more accurate.

How many bags of mortar do I need for 100 blocks?

About 7 to 8 bags at 80 lb each. Each block uses about 0.0417 cubic feet of mortar, so 100 blocks need 4.17 cubic feet, and one 80 lb bag makes 0.6 cubic feet (4.17 / 0.6 = 6.95, rounded up to 7).

How much does a standard concrete block weigh?

About 38 lb for a standard 8x8x16 hollow block. A pallet of 90 blocks weighs roughly 3,400 lb. Lightweight blocks made with expanded aggregate weigh about 28 lb each.

Do I need a footing for a concrete block wall?

Yes. A block wall needs a concrete footing at least 8 inches deep and twice as wide as the wall, on undisturbed ground. Without a footing the wall will settle unevenly and crack.