Sand Calculator
Work out how much sand you need for a sandbox, paver base, playground, or leveling job — in cubic yards, tons, and bags.
Sand Calculator
Density defaults to 100 lb per cubic foot for dry sand. Wet sand can weigh 120 lb per cubic foot or more, so the weight is an estimate — order by volume where possible.
Formulas:
Volume (cu ft) = Length (ft) × Width (ft) × Depth (in) ÷ 12
Volume (cu yd) = Volume (cu ft) ÷ 27
Weight (lb) = Volume (cu ft) × density (100 lb/cu ft dry, up to 120 wet)
Tons = Weight (lb) ÷ 2,000 | 50 lb bags = Volume (cu ft) ÷ 0.5, rounded up
What Does a Sand Calculator Do?
A sand calculator works out how much sand you need for a sandbox, a paver base, a playground, a volleyball court, or a leveling job. You enter the length, width, and depth of the area, and it returns the volume in cubic yards and cubic feet, the weight in pounds and tons, and how many 50-pound bags that equals if you are buying bagged sand instead of bulk. A waste allowance is built in, because sand settles, spills, and is never spread perfectly evenly.
Sand is sold two ways: in bulk by the cubic yard from a landscape or aggregate supplier, and in bags from a home center. Bulk is far cheaper per cubic foot, but it comes with a delivery charge and usually a 1-cubic-yard minimum. Bags are convenient for small jobs — a sandbox or a paver repair — but expensive at scale: a job that needs 1 cubic yard of sand would take 54 bags at 0.5 cubic feet each. This calculator gives you both numbers so you can choose the cheaper route for your job size.
How to Use This Calculator
Measure the area in feet: the length and the width of the sandbox, patio, or playground. Then enter the depth in inches — 6 inches is a good depth for a sandbox, 1 inch of sand is the bedding layer under pavers, and 9 to 12 inches is the fall-zone depth recommended under playground equipment. The density field defaults to 100 pounds per cubic foot, the standard estimating figure for dry sand; leave it there unless your supplier quotes a different figure. The waste allowance defaults to 10%: sand compacts after it is spread and watered, and some always spills during handling.
The headline result is cubic yards, because that is how bulk sand is sold. The bag count is there for small jobs: if the calculator says you need 64 bags, check the price of a 1-yard bulk delivery before you load your car — bulk usually wins once you pass about 15 to 20 bags.
The Sand Formula
The volume of a rectangular area is length times width times depth. Length and width are measured in feet, but depth is measured in inches, so depth must be divided by 12 first. A sandbox 8 feet long and 8 feet wide, filled 6 inches deep, is 8 × 8 × 6 ÷ 12 = 32 cubic feet. Divide cubic feet by 27 to get cubic yards (there are 27 cubic feet in a cubic yard), so the sandbox needs 1.19 cubic yards.
Weight comes from density. Dry sand weighs about 100 pounds per cubic foot — the standard figure used by aggregate suppliers for estimating. Multiply 32 cubic feet by 100 and you get 3,200 pounds, or 1.6 tons. With the 10% waste allowance, the volume becomes 35.2 cubic feet (1.30 cubic yards) weighing 3,520 pounds (1.76 tons). For bags, one 50-pound bag of sand holds about 0.5 cubic feet, so 35.2 cubic feet needs 35.2 ÷ 0.5 = 70.4 bags, rounded up to 71.
Density varies with moisture more than with anything else. Dry sand is about 100 pounds per cubic foot, but wet sand — after rain, or fresh from a river dredge — can weigh 120 pounds per cubic foot or more, because the water fills the gaps between the grains. That is a 20% swing in weight for the same volume, which is why you should order sand by volume (cubic yards) whenever you can, and treat the tonnage as an estimate. If your supplier sells by the ton, ask what density they use for their sand.
Which Sand for Which Job?
Not all sand is the same, and using the wrong type causes problems. Play sand — washed, screened, and fine-grained — is the right choice for sandboxes and play areas, because it is clean, soft, and free of sharp particles. Mason sand (also called mortar sand) is fine and uniform, and it is used for mortar, plaster, and as a paver bedding layer. Concrete sand is coarser, with angular grains that lock together, and it is used in concrete mixes and as a base under pavers. Polymeric sand is a special product for filling paver joints: it hardens when wet and resists weeds and ants, but it is far more expensive than regular sand and should only be used for joints.
For a paver patio, the usual build-up is 4 to 6 inches of compacted gravel base, then 1 inch of coarse bedding sand, screeded level, with the pavers laid on top and the joints filled with fine sand. The bedding layer is the one this calculator is most often used for: a patio 20 feet by 15 feet needs 1 inch of sand, which is 20 × 15 × 1 ÷ 12 = 25 cubic feet, or 0.93 cubic yards — just under a yard, so one bulk delivery covers it.
Worked Example
Say you are filling a sandbox 8 feet long and 8 feet wide, 6 inches deep. The volume is 8 × 8 × 6 ÷ 12 = 32 cubic feet, which is 32 ÷ 27 = 1.19 cubic yards. At 100 pounds per cubic foot, that is 3,200 pounds — 1.6 tons. Add the 10% waste allowance and you should order 1.30 cubic yards, or 35.2 cubic feet. If you buy bags instead, 35.2 cubic feet divided by 0.5 cubic feet per 50-pound bag is 70.4, rounded up to 71 bags. At roughly $5 per bag, that is about $355 — while a bulk delivery of 1.5 cubic yards of play sand typically costs $50 to $100 plus a delivery fee, which is why bulk wins for anything over about half a yard.
For a paver bedding job — a patio 20 feet by 15 feet at 1 inch deep — the volume is 20 × 15 × 1 ÷ 12 = 25 cubic feet, or 0.93 cubic yards, weighing 2,500 pounds (1.25 tons). With a 10% allowance, order 1.02 cubic yards. On a job this size, one bulk yard covers it with a little to spare, and buying bags would take 55 bags for the same amount of sand.
Tips for Ordering Sand
Order by volume, not weight. Because wet sand is 20% heavier than dry sand, a ton of sand can be anywhere from 16 to 20 cubic feet. Ordering by the cubic yard removes the moisture guesswork entirely.
Ask what type you are getting. "Sand" at a landscape yard could be play sand, mason sand, concrete sand, or fill sand, and the prices and uses are different. Tell the supplier what the job is and let them recommend the type — and ask whether it is washed and screened.
Protect the delivery spot. Bulk sand is dumped in a pile where the truck can reach, usually the driveway. Lay down a tarp first: sand is much harder to sweep off paving than soil, and rain will wash it into every crack and drain nearby.
Cover a sandbox when it is not in use. An uncovered sandbox collects rain, leaves, and animal waste. A simple cover keeps the sand clean and dry, which also keeps its weight down if you ever need to move it.
Common Mistakes to Avoid
The biggest mistake is entering the depth in feet instead of inches, which makes the volume 12 times too large. If the answer looks wildly wrong, check the units first. The second mistake is forgetting that sand settles and compacts: a sandbox filled exactly to the top will drop an inch or two after the first rain and a few weeks of play, so fill it slightly proud and top it up once a year.
The third mistake is using the wrong sand. Fill sand is cheap but full of clay and stones — fine for raising ground level under a shed, terrible for a sandbox or under pavers, where it will stain and settle unevenly. And never use beach sand for construction: the salt corrodes metal, and the rounded grains do not lock together the way angular quarry sand does. Finally, do not buy bagged sand for a big job: at 0.5 cubic feet per bag, a 1-cubic-yard job needs 54 bags, and the cost per cubic foot is typically three to five times the bulk price.
Results from this calculator are estimates for planning and ordering. Sand density varies with moisture and grain size, so confirm the weight per yard with your supplier if you are ordering by the ton.
Frequently Asked Questions
How much sand do I need for an 8x8 sandbox 6 inches deep?
1.19 cubic yards before waste, or 1.30 cubic yards with a 10% allowance. The volume is 8 x 8 x 6 / 12 = 32 cubic feet, and there are 27 cubic feet in a cubic yard.
How much does one cubic yard of sand weigh?
About 2,700 lb, or 1.35 tons, at the standard dry density of 100 lb per cubic foot (27 x 100 = 2,700). Wet sand can weigh up to 3,240 lb per yard.
How many 50 lb bags of sand are in a cubic yard?
54 bags. A 50 lb bag holds about 0.5 cubic feet, and a cubic yard is 27 cubic feet (27 / 0.5 = 54).
How deep should sand be under pavers?
1 inch of coarse bedding sand, screeded level, over 4 to 6 inches of compacted gravel base. The sand layer is only for leveling — the gravel base does the structural work.
What is the difference between play sand and mason sand?
Play sand is washed, screened, and fine-grained for sandboxes and play areas. Mason sand is also fine and uniform but is made for mortar and plaster, and it works well as a paver bedding layer. Both are washed; fill sand is not.